CJ Appliance Repair(918) 992-4002

Top-load and front-load washers

Washing machine repair in Tulsa, OK

A tub of gray water, a spin that never comes, a washer walking across the floor. Tell Colby what it’s doing and whether it loads from the top or the front.

4.9694 Google reviews
Repair ticketNo. 4002

My . It’s a in .

Or send it as a requestTexting? Add a photo of the model tag.

  • Colby answers his own phone
  • Most visits within 48 hours, often same day
  • Diagnostic fee waived when he does the repair
Text

The trouble chart

What’s your washer doing?

If your…It’s usually…Colby checks
Washer won’t drainSomething caught in the pump or its filter, a kinked drain hose, or a pump that failedThe pump and filter, the hose, the lid or door lock
Washer won’t spinA lid lock that won’t confirm, a worn belt or motor coupling, or the shifterThe lock, the belt or coupling, the motor, the board
Washer leakingA torn door boot on a front-loader, a loose hose, a worn tub seal, or a cracked tubWhere the water starts, then the boot, hoses, pump, tub
Washer won’t startA door that won’t lock, a broken lid switch, a dead control board, or no powerPower, the lid switch or door lock, the control
Washer shaking or loudWorn suspension rods or shocks, a failing tub bearing, or a load bunched to one sideThe suspension, the bearings, how level it sits
Washer won’t fillSupply valves closed or hoses kinked, clogged inlet screens, or a failed inlet valveThe supply, the inlet valve, the pressure switch

Three kinds of washer

How your kind of washer usually fails

01

Top-load with an agitator The classic

It fills deep, the post in the middle swirls the clothes, then the tub spins. The lid switch, the motor coupling and the agitator’s plastic dogs are the parts that wear.

Colby checks the lid switch first, then the drive parts underneath.

02

High-efficiency top-load No agitator

It uses a low wash plate and much less water, and locks the lid while it runs. A lid lock that won’t confirm, worn suspension rods, or the shifter that moves it from wash to spin stops most of them.

He tests the lid lock and the shifter, and checks the suspension for wear.

03

Front-load Door on the front

It seals with a rubber door boot and keeps the door locked for the whole cycle. A torn boot, a pump filter packed with lint and coins, and worn drum bearings are where front-loaders go wrong. When a drum rusts through, the whole drum gets replaced.

He checks the lock, the boot, the pump and the bearings, and has replaced whole drums.

Parts he replaces

What Colby fixes on a washer

  • Drain pumppushes the water out; coins and socks jam it
  • Lid switch or door locktells the washer it’s safe to run
  • Water inlet valvelets the hot and cold water in
  • Drive belt and motor couplingconnect the motor to the tub
  • Shift actuatorswitches an HE washer between wash and spin
  • Suspension rods and shockskeep the tub steady in the spin
  • Door bootthe rubber seal on a front-loader
  • Tub bearings and sealthe roar that grows louder each spin
  • Pressure switchsenses how full the tub is
  • Control boardruns every cycle
Model
▒▒▒▒▒▒▒
Serial
▒▒▒▒▒▒▒▒▒

Before you call

Where’s the model number?

The model and serial number tell Colby exactly which parts your appliance takes. Here’s where to look.

  • Top-loader Lift the lid and look along the back edge of the opening, under the lid itself, or on the back panel.
  • Front-loader Open the door and check the rim around it, or behind the small access door at the bottom front.
  • Stacked pair? The washer’s tag is on its own door frame; if both machines act up, text Colby both tags.
Text Colby a photo of the tag

From his job files

Recent washer repair jobs

Questions

Washer repair: questions people ask

Q

My front-loader smells musty. Is that a repair?

ANot at first. Leave the door open between loads, wipe out the folds of the rubber boot, and clear the pump filter at the bottom front with a towel down for the water that comes out. If the smell won’t leave, or the boot is torn, Colby can replace it.

Q

Is a shaking washer worth fixing?

AFirst make sure it sits level and the load isn’t bunched to one side. Most shaking after that comes from worn suspension rods or shocks, which are modest parts. A drum bearing that has started to roar is a bigger job, and Colby will tell you which you have before any work starts.

Q

It stopped full of water. Should I bail it out?

AYou don’t have to. Leave it, put a towel down if it’s seeping, and Colby will drain it when he gets there. If it’s a front-loader, don’t force the door; it stays locked while water is inside.

Q

Do you charge to come out?

AYes. There’s a diagnostic fee for the visit, and if you have Colby do the repair, the diagnostic fee is waived.

Q

How soon can you come?

AMost appointments are within 48 hours, many within 24, and often the same day. Call or text and Colby will give you the soonest time he has.

Rather type it out?

Request washer repair in Tulsa

Tell us what's wrong and how to reach you. Colby will call or text you back.

  • Calls and texts(918) 992-4002
  • Tulsa, Oklahomaand the towns around it
  • Texting?A photo of the model tag helps Colby know what he’s working on.
Repair requestCJ Appliance Repair

Tulsa · (918) 992-4002

Broken appliance? Call Colby.

Call (918) 992-4002